Elevator apprentice practice tests Free Beta
Pick a year and go. Every answer tells you why.
Every question has four choices, an explanation of the right answer, a note on why each wrong answer is wrong, and the code rule it comes from. The years and modules follow the CEIEP curriculum outline.
Year 1: 144 questions
Safety, the code book, ladders and rigging, print reading, escalators, hydraulics and installation.
- Module 1: Safety (15 questions)
- Module 2: Introduction to Elevating Devices and Applicable Codes (15 questions)
- Module 3: Ladders and Scaffolding (15 questions)
- Module 4: Rigging and Hoisting (15 questions)
- Module 5: Mechanical Print Reading (12 questions)
- Module 6: Escalators, Moving Walks and Cart Conveyors Installation and Maintenance (15 questions)
- Module 7: Basic Hydraulic Elevator Installation (15 questions)
- Module 8: Traction and Hydraulic Elevator Installation (42 questions)
Sample Year 1 question: An old freight elevator has solid blocks in the pit where you'd expect buffers. What does the code call a device like that, one that isn't an oil, spring or elastomeric buffer?
Answer: A bumper
It's a bumper. A bumper is a plain solid stop that takes the hit when the car or counterweight runs down past its bottom limit. Oil, spring and elastomeric (rubber-like) stops do the same job, but those are what the code calls buffers. Code rule: 1.3 bumper.
Year 2: 90 questions
Basic electricity, AC and magnetism, solid-state electronics and control devices.
- Module 9: Basic Electricity (22 questions)
- Module 10: Alternating Current, Magnetism and Transformers (22 questions)
- Module 11: Solid State Electronics (22 questions)
- Module 12: Industrial Electricity for Elevating Devices (24 questions)
Sample Year 2 question: A relay coil in a 24 V DC control circuit measures 480 Ω. How much current does it draw?
Answer: 50 mA
I = V ÷ R = 24 ÷ 480 = 0.05 A, which is 50 mA. To turn amps into milliamps, multiply by 1 000.
Year 3: 89 questions
Motors, motor starting, circuit tracing and troubleshooting.
- Module 13: AC and DC Motor Principles for Elevating Devices (24 questions)
- Module 14: Motor Starting (23 questions)
- Module 15: Circuit Tracing (21 questions)
- Module 16: Troubleshooting Procedures (21 questions)
Sample Year 3 question: An MG set's drive motor, started across the line with its windings in delta, draws 180 A at the moment it starts. It's moved to a wye-delta starter, so it now starts in wye and switches to delta once it's up to speed. About what starting line current does it draw now, and how much starting torque does it have compared with a delta start?
Answer: 60 A, with about a third of the torque
60 A and about a third of the torque. In wye each winding gets the line voltage ÷ 1.732 (the square root of 3), so its current drops by 1.732. In delta the line current was 1.732 times the winding current, so leaving delta takes off another 1.732: 1.732 × 1.732 = 3, and 180 ÷ 3 = 60 A. Torque follows the winding voltage squared, (1 ÷ 1.732)² = 1/3. You give up torque to cut the inrush that can dip the building's supply, which is fine for a motor that starts nearly unloaded, like an MG set.
Year 4: 124 questions
Mechanical work, lifts and hoists, alterations, CSA B44 maintenance and equipment maintenance.
- Module 17: Mechanical Work Practices (15 questions)
- Module 18: Lifts for Persons with Physical Disabilities (10 questions)
- Module 19: Manlifts, Personnel Hoists and Material Hoists (10 questions)
- Module 20: Modernization/Alterations (15 questions)
- Module 21: CSA B44 Maintenance (15 questions)
- Module 22: General Preventative Maintenance (15 questions)
- Module 23: Elevator Machine Room Equipment Maintenance (14 questions)
- Module 24: Elevator Car Equipment Maintenance (15 questions)
- Module 25: Elevator Hoistway and Pit Equipment Maintenance (15 questions)
Sample Year 4 question: Your crew is modernizing a traction elevator first installed in 1985: new controller, new door equipment. Under 8.7.1.1, what is the least the finished installation has to meet?
Answer: The code it was installed under, today's code for the alteration work itself, and A17.3 too where the authority has adopted it
8.7.1.1 sets a floor of three things: the whole installation still meets the code it was installed under, the alteration work meets the code in force when it's done, and ASME A17.3 applies too where the authority having jurisdiction has adopted it. The rest of Section 8.7 then lists which newer rules each kind of alteration brings in, so an alteration doesn't mean the whole unit gets upgraded. Code rule: 8.7.1.1.
This is a Beta, so if an answer doesn’t match your code book, go by the book. Code questions are written from A17.1-2016/CSA B44-16 and matched to the 2019 and 2022 editions; electrical questions come from general principles. Years and modules follow the CEIEP curriculum outline, with thanks; this practice set is not made or endorsed by CEIEP. New to the trade? Read how to become an elevator mechanic.